Fixing and sliding supports
Solutions for pipes with thermal expansion
Installation of pipelines is a complex process that requires taking into account not only the loads from its own weight, but also the influence of temperature deformations. An incorrect approach can lead to leaks, shortening the system lifetime and deformation of the system.
UTECH's solution allows you to effectively control thermal expansion. Thanks to a suitable combination of UTECH sliding and fixing supports, you can give the pipeline system a well-defined structure in which the pipe movement is evenly distributed along the route.
UTECH's solution allows you to effectively control thermal expansion. Thanks to a suitable combination of UTECH sliding and fixing supports, you can give the pipeline system a well-defined structure in which the pipe movement is evenly distributed along the route.
Our solutions
F =4 kN, Hmin =150 mm, Hmax =500 mm
F =9 kN, Hmin =190 mm, Hmax =500 mm
F =8 kN, Hmin =190 mm, Hmax =500 mm
F =4 kN, Hmin =225 mm, Hmax =2000 mm
F =8 kN, Hmin =185 mm, Hmax =2000 mm
F =14 kN, Hmin =175 mm, Hmax =2000 mm
F =36 kN, Hmin =200 mm, Hmax =2000 mm
F =36 kN, Hmin =200 mm, Hmax =2000 mm
F = 8 kN, Hmin = 95 mm, Hmax = 175 mm
F = 4 kN, Hmin = 85 mm, Hmax = 115 mm
F =2 kN, Hmin =85 mm, Hmax =115 mm
Coefficient of friction - 0,18
Advantages
Perfect fit for both horizontal and vertical pipelines
Wide range of applications for fixing pipes at a distance from the base from 0.085 m to 2 m with a maximum load of 36 kN
MSG transverse sliding supports allow the pipe to move in two directions, which is especially important when the pipeline route turns
Maximum flexibility in the location of anchor holes, which allows you to avoid hitting the reinforcement
The bearing capacity of the elements and the coefficient of friction have been confirmed by calculations and field tests
Engineering support in the calculation and placement of supports in the START software package
Comparison of UTECH solution with a traditional method
Modern installation systems outperforms from the traditional method using metal welding in the speed of installation, durability of the structure and ease of operation.
UTECH solution
- Easy and fast installation
- The installation is carried out by one employee without special qualifications
- Installation is carried out with a standard set of tools
- Reliable fastening – the use of anchors with high load-bearing capacity confirmed by certificates
- The estimated axial load of the pipe clamp is from 400 kg
- Galvanized coating that does not require additional processing
- Aesthetic appearance - neat shape of the support
Traditional solution (welded metal)
- Labor-intensive and time-consuming installation
- Additional measures are required to organize work in compliance with safety regulations
- The installation is carried out by two employees: a welder and an installer.
- Welding where damage to pipes is possible in case of thin-walled pipes
- Unreliable fasteners – the use of anchors with low bearing capacity
- Not possible to use with welding of the stainless and galvanized pipes according to SP73
Comparison of the installation time for the traditional method and the UTECH solution
The choice between traditional installation using welded metal and modern UTECH installation systems depends on many factors, such as the specifics of the project, budget, installation time requirements and durability.
Traditional methods can be a good solution under certain conditions, however, UTECH installation systems offer significant advantages in installation speed, weight, stability and reliability. Therefore, when choosing a method, it is necessary to carefully evaluate all factors and choose the optimal solution in each specific case.
Traditional methods can be a good solution under certain conditions, however, UTECH installation systems offer significant advantages in installation speed, weight, stability and reliability. Therefore, when choosing a method, it is necessary to carefully evaluate all factors and choose the optimal solution in each specific case.
Design services
-
Development of projects with required degree of detail - Calculation of steel structures and units according to methods SP 16, SP 20, STO-064 (using LIRA software)
- Calculation and design of engineering systems and equipment (using START software)
- BIM modeling
-
Development of standard albums and solutions for the project -
Blueprinting
Advantages of working with UTECH
-
Official successor of Hilti in RussiaWe operate in the Russian market since 1993 -
Own designing capacity4 engineering centers are located in Moscow, St. Petersburg, Samara, Rostov-on-Don within the framework of the UDMLab Design Institute -
Local productionOwn production facility in St Petersburg & OEM partnerships allowed to localize production in the Russian Federation -
More than 3 000 projects annuallyWe have expertise to support many projects at the same time -
More than 500 employeesWe have resources and a large number of professional staff -
The product is on stockWe have warehouses with an area of more than 15 000 m
Contact us
Please fill out the form and we will contact you within one business day
By clicking on the button, you consent to the processing of personal data and agree to the privacy policy
Leningradskaya str., b. 25,
Khimki, Moscow region, Russia,
141400
Khimki, Moscow region, Russia,
141400
UTECH is the official legal successor
Hilti Group in Russia
Hilti Group in Russia
SETTINGS
Cookies, which are necessary for the correct operation of the website, are always enabled. Other cookies are configured
Any other questions? Contact us!
By clicking on the button, you consent to the processing of personal data and agree to the privacy policy